Check path to models and symlinks, if you have any.
/home/user/folder/stable-diffusion-webui/models/Stable-diffusion/
Monday, July 31, 2023
Saturday, July 15, 2023
Toshiba DT01ACA200 SMART
smartctl --all /dev/sda (Prints all SMART information)
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.19.0-46-generic] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" DT01ACA... Desktop HDD
Device Model: TOSHIBA DT01ACA200
Serial Number: #########
LU WWN Device Id: 5 000039 ff3e0f0aa
Firmware Version: MX4OABB0
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database 7.3/5319
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jul 15 22:29:35 2023 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (14822) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 247) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 070 070 016 Pre-fail Always - 181274516
2 Throughput_Performance 0x0005 139 139 054 Pre-fail Offline - 72
3 Spin_Up_Time 0x0007 127 127 024 Pre-fail Always - 296 (Average 299)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 3238
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 2005
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 32025
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2840
192 Power-Off_Retract_Count 0x0032 097 097 000 Old_age Always - 4030
193 Load_Cycle_Count 0x0012 097 097 000 Old_age Always - 4030
194 Temperature_Celsius 0x0002 240 240 000 Old_age Always - 25 (Min/Max 14/52)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2598
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 32022 hours (1334 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 50 30 cd 73 08 Error: UNC at LBA = 0x0873cd30 = 141806896
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 50 28 30 cd 73 40 08 00:01:48.986 READ FPDMA QUEUED
60 08 20 08 cd 73 40 08 00:01:45.998 READ FPDMA QUEUED
60 08 68 00 cd 73 40 08 00:01:42.921 READ FPDMA QUEUED
60 08 60 00 54 5a 40 08 00:01:42.861 READ FPDMA QUEUED
60 08 58 f8 cc 73 40 08 00:01:39.840 READ FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 32022 hours (1334 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 f0 cc 73 08 Error: UNC at LBA = 0x0873ccf0 = 141806832
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 68 f0 cc 73 40 08 00:01:32.621 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 08 00:01:32.600 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 00:01:32.600 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:01:32.597 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:01:32.597 SET FEATURES [Set transfer mode]
Error 2 occurred at disk power-on lifetime: 32022 hours (1334 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 f0 cc 73 08 Error: UNC at LBA = 0x0873ccf0 = 141806832
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 a8 f0 cc 73 40 08 00:01:28.814 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 08 00:01:28.814 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 00:01:28.814 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:01:28.812 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:01:28.812 SET FEATURES [Set transfer mode]
Error 1 occurred at disk power-on lifetime: 32022 hours (1334 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 30 00 cd 73 08 Error: UNC at LBA = 0x0873cd00 = 141806848
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 40 48 f0 cc 73 40 08 00:01:18.230 READ FPDMA QUEUED
60 08 20 68 f1 ad 40 08 00:01:18.216 READ FPDMA QUEUED
60 00 18 18 5f bd 40 08 00:01:17.959 READ FPDMA QUEUED
60 00 10 18 5e bd 40 08 00:01:17.958 READ FPDMA QUEUED
60 00 08 18 5d bd 40 08 00:01:17.958 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Subscribe to:
Posts (Atom)